When taking a digital thermostat from a cold van and installing it in a warm home, you should be aware that it won’t respond instantaneously. These settings appear in the installer menu and it is important to select the setting for your heat source: gas boiler (default), oil boiler, heat pump, or electric heating A home’s general temperature can be set to 21˚C, but installers can use TRVs to control the temperature in certain rooms, for example where part of a home has been developed to incorporate a ‘granny flat.’ Step by Step - Installing miGenie

This groups weekdays and the weekend separately, so you can set a schedule for your weekdays and a separate schedule for the weekend. Put the SCR unit into its learn mode. Press and hold button number 1 and then do the same to button number 2. The red light will flash a couple of times before going out. Then release both buttons – the two LED lights should be on.

Similar products

It’s also worth making sure that the householder understands that altering the temperature on a room thermostat will only be effective if a programmer has set the heating to be on. If the homeowner wants the heating on when the programmer has it set to be off, they need to understand they have three options: Advise householders that concealing a TRV with furniture or behind a curtain will affect the performance of their system, making it less reliable as the TRV cannot accurately sense the temperature of the room. Advising customers on room thermostat settings The miGenie thermostat and miGenie gateway are pre-bound to the miGenie controller so they just need to be positioned in the best place for wireless communication. To help with this, there is a built-in signal strength indicator. When a boost is selected, a timer symbol appears in the bottom right of the display and remains until the next event. When used with electric heating the Digistat cycles the heater at 12 cycles per hour to maintain room temperature and save money.

They can ‘advance’ the heating, which means the programmer will skip to the next ‘on schedule’ and the heating will remain on until that programme is due to end.Thermostatic radiator valves (TRVs) are an important part of the central heating system, as they allow householders to control the temperature of each individual room through the radiator. This option has no schedule and controls by temperature only. You set your preferred temperature and adjust it with the + and - buttons.

To learn more about TRVs, complete our e-learning module here Help customers to programme their system The industry recommendation for a room thermostat is 21˚C, but this may need to be adjusted if there are health considerations or elderly occupants that require a warmer environment. When used with a gas boiler the Digistat will automatically cycle the boiler to help your boiler to run more efficiently and save you 10% on your heating bill (compared to a simple ON/OFF thermostat).Reset the Digistat thermostat by going into the setting menu, selecting the Inst03 menu (installer settings) and then rSEt20 to reset to factory settings. Then remove the batteries. Plug the mains power cable into the gateway then connect the network cable from the gateway to the router. There are also known issues when pairing with Samsung smartphones using Android 11. Please change to an earlier or later version of Android. There may be other Digistats powered up and within range and this will slow down the pairing process. If it is possible to depower the other Digistat please do this while you are pairing, or if not then press “I have done these steps” and wait for the RETRY button to appear. On the second attempt the pop-up should appear instantly. On the controller, navigate to ‘signal strength’ through the settings on the screen. On the thermostat, press and hold the + and – buttons for five seconds, then navigate to signal strength

The Green Premium eco-mark stands for complete, transparent, and easily available information about products The receiver unit should be positioned 300mm away from any metal objects such as the boiler or a microwave or any large obstructions like solid walls that will affect the signal being sent from the transmitter to the receiver. Replacing a timeswitch with a wireless programmable thermostat Depending on the fuel type you select during installation will affect how Digistat works with your boiler/heat source - so ensure to select the correct type during installation. Does Digistat work with combi-boilers and conventional boilers? Finally, if the additional requirement for heat is likely to be regular, they can re-programme their control to include a new time period.

A frost protection thermostat is fitted in the same space as the boiler or most at risk part of the system, and works alongside the pipe thermostat, totally independently from all other timers and thermostats. In hard water areas it is more important than ever that TRVs are maintained to stop plastic degrading and valves failing. Hold the transmitter unit 2 metres away from the SCR unit and then replace the batteries in the transmitter.