This article was co-authored by Claudia & Angelo Zimmermann and by wikiHow staff writer, Hunter Rising. Claudia and Angelo Zimmermann are the founders of Everneat, an Eco-Friendly Cleaning Service based in New York City and in Connecticut. They are also the founders of Clean Code, a DIY 100% natural cleaning product line. Wet sanding slowly levels out the surface of the plastic with a bit more force than toothpaste or baking soda, making it ideal for deeper scratches. Moisture keeps material from building up in the sandpaper, preventing further scratches from marring the plastic. It’s worth noting that scratches can be removed more easily from acrylic than polycarbonate, so you may not have as much success if the damaged material is a polycarbonate sheet. Naturally, lighter scratches can be buffed out more easily than deeper ones. Set your heat gun to the lowest setting. Plug in your heat gun and look for the buttons or dial on the side that control the temperature settings. Press the arrow buttons or turn the dial to set it to the lowest heat setting available. [12] X Research source

Removing surface scratches from acrylic only requires a few simple tools and a bit of determination. In this how-to guide, we will walk through how to evaluate scratches and provide instructions for repairing light and moderate scratches in acrylic. Alternate between the above two steps for about four minutes. Your acrylic will look rough – this is fine. Proceed to the next step if your scratches are pretty light or skipstraight to Step4 if you’re attempting to buff out a bit of a gouge. STEP 3: First buffusing a mild abrasive, like toothpaste or baking soda. Angelwax says it can be used to remove up to 2,500-grade sanding marks. Along with the rest of the top four here, it topped the results for finish improvement, leaving a shine in stark contrast to untreated areas and most of its rivals’ attempts. It had trouble with the plastic ice scraper marks, but fared better on the fine knife line, where it only had to give best to ValetPRO. A competitive price was enough to give it a narrow victory over the similar Advanced Compound. We didn’t have high expectations of Tripple, because products that aim to improve and protect paint tend to do neither well. We didn’t test what kind of water-repelling finish Tripple left, but it certainly improved our tired paint. And it was adding a shine where Tripple excelled, matching the best with a glossy finish. It struggled to make the same headway with the plastic and metal blade marks as our top two, but did reduce their impact. And with a keen price, that was enough to put it in our top four.This article was co-authored by Jon Gholian. Jon Gholian is a Cleaning Specialist and the Founder of Cleany, a home and office cleaning concierge service based in New York City, New Jersey & Miami. Cleany specializes in providing quality cleaning and handyman services to all their customers. All Cleany employees are insured, bonded, and professionally trained. Cleany has been featured in the New York Times, Bravo & Redfin. Wet one piece of 600 grit sandpaper - run it over the scratched area in a circular motion and repeat with a dry piece of 600 grit sandpaper too. Rub with both wet and dry sandpapers for around 3 to 3 minutes. Don't worry if your acrylic looks more frosty or scratched - this will go away during the process.

Wet one piece of 800 grit sandpaper - run it over the scratch in a circular motion and repeat with a dry piece of 800 grit sandpaper. Alternate between the dry and wet sandpaper, rubbing for 2 to 3 minutes. Don’t worry if your acrylic begins to look more frosty or appear to have more little scratch marks on it - this will go away during the process. Wet a piece of 800-grit sandpaper. Run a piece of 800-grit sandpaper underneath warm water to get it damp. Shake any excess water off of the piece and wring it out so it doesn't drip. Set up your work station near a sink if possible so you can re-wet the sandpaper whenever you need to. [1] X Research sourceTake a dry, clean cotton or microfiber cloth. Wipe away any fragments Warning: A dirty cloth could scratch the acrylic all over again! Wipe the scratch remover off the plexiglass with a dry cloth. As soon you're done applying the scratch remover to the plexiglass, use a lint-free cleaning cloth to wipe any excess off. Work in small circles over the surface of your plexiglass. Once the scratch remover is off of your piece, you won't be able to see the scratches anymore. [11] X Research source

Use finer grit sandpaper if necessary. Examine the scratch area. It should look different, and the scratch may have been removed. If it’s still visible, however, you can try rubbing it again with a finer grade of sandpaper. Try 1200 grit, for instance, and follow the same procedure as before. Cleaning Specialist Expert Interview. 15 December 2020. Gently rub it in a circular motion all around the scratch. This will remove any dirt and grease, making it easier to get rid of the scratch. Dry the area with a clean, dry cloth when you’re done. [2] X Research source You can use a microfiber towel. [3] X Expert Source Jon Gholian Take a good look at these mild scratches. If the scratches are only visible upon close inspection, sandpaper may not be necessary. Instead, use an abrasive acrylic polish (we recommend Novus No. 2) directly on the scratched area and apply consistent, moderate pressure to a clean, soft rag. Move it in a circular motion until you can’t see the scratches. This could take a few minutes, so don’t panic if the scratches don’t disappear immediately. When you believe the acrylic is smooth, gently wipe off the compound with a clean cotton or microfiber towel.

Fenwicks Windowize Scratch Remover 100ml

House Cleaning Professionals Expert Interview. 12 July 2019. Run the cleaning cloth under warm water until it's completely saturated. Wring the cloth out so it isn't dripping wet when you use it. [7] X Research source Take a dry, clean cotton or microfiber cloth. Wipe away any fragments. Warning: A dirty cloth could scratch the acrylic again! The depth of a scratch dictates how to remove it. Generally, if you run your fingernail over the scratch and the nail doesn’t hook, it’s shallow enough to be successfully treated with light abrasives, such as toothpaste or baking soda. If the nail does catch, however, it’s a deeper scratch that will require a series of passes with a super-fine grit wet sandpaper. STEP 2: Get it squeaky clean. Apply toothpaste to a damp cloth. A mild abrasive, like toothpaste, helps wipe the scratch away. Use a paste variety, not a gel one. You won’t need to put much on the cloth. Just use enough that you can smear it all over the scratch. Instead of toothpaste, you could also try: [5] X Research source